How set-by-set adaptation works
Reviewed November 7, 20266 min read
On this page
After each set you log, VidarFit looks at what you actually did and decides whether the rest of that exercise should get heavier, stay the same, get lighter, change, or stop. It shows the reason on the card for the next set: Up next, or the pairing’s name, such as Superset A.
On a day of a program you built, or a saved workout, the targets you wrote stay as written for the whole workout, and the card says so. Pain still stops an exercise, and loads still move between sessions.
What it looks at
The load and reps you logged, how many reps you had left (if you said), whether you reached failure, any pain, the target range, earlier changes in the session, and the loads your equipment can actually make.
An easy set
If a set clearly beat the target with plenty left in reserve, the next set may go up by one step: the smallest jump your equipment allows. For muscle-building work, that happens at 15 or more reps with 3 or more in reserve, unless the next weight you have is a big jump: then the weight stays and your reps build first. Most other work goes up between sessions instead. If a set after the first falls short at a step of more than 20%, or your only set there does, the next session goes back to the lighter weight, and your reps build there before the next try. After a smaller step, the next session stays at the heavier weight. After two tries the weight stays until you lift the heavier one, for up to eight sessions from the first try. While an exercise is still finding your working weight, because it has no history of its own yet, an easy set can raise the next one on any goal, and the Up next card says how far and why. On a saved workout or a day of a program you built, that doesn’t happen: the targets stay as written, so if a starting weight is clearly too light, pick a heavier one, and what you lift becomes your starting point. With no history of its own and no usual weight from you, an assisted exercise starts with the most help your equipment gives. In a workout the Forge plans, 15 or more reps with 3 or more in reserve takes away one step of help, whatever the target range. Fewer than 8 reps, or a set you couldn’t finish, adds help.
A hard set
If you fell short of the range, the remaining sets usually get lighter so you can finish them inside the target. A bodyweight exercise has no weight to take off, so its rep target comes down to what you did, and it climbs back from your best set over the next sessions. A split squat or a step-up done with bodyweight keeps its own range instead, because balance limits it, and its card says so. For muscle-building work, the remaining sets also get lighter when you only just reach the bottom of the range with nothing left. The drop is 15% on muscle-building work and 10% on strength work, or 5 lb (about 2.3 kg) if that’s more, then snapped to a load you can actually make. Two cases keep the weight: at the lightest that bar or rack goes, and for your first three sessions on a jump of more than 20% to your next weight, when you finished the set and your reps in reserve were within the plan. The card says why. On powerlifting top-set days, the back-off sets follow your top set’s weight instead: a back-off that ends short keeps its weight, and one you couldn’t finish, or one that ends clearly closer to failure than planned, stops the rest.
Effort left blank
Effort is the Reps in reserve field on each set. A blank answer, or Not sure, means unknown. It is never read as “easy”, so during a workout VidarFit will not add weight on reps alone when it cannot tell how hard the set was. For your next session, one rep more than an answered set needs can still earn one step, and after a session at the top of the card the next card offers that rep, when there’s a heavier step to earn and the day allows one. Outside muscle-building work, and on a program you built or a saved workout, every working set has to get there. A program you built or a saved workout keeps its reps, so the card on its first set says what a step takes: three sessions in a row at the top of the card, or one rep past the top on every set. Reps in reserve can stay blank, and a number counts if it’s the card’s at the top, or one under it on the extra rep. A number can earn it sooner if it shows you can lift the next weight. If nothing can, the card says the step is too big, and you can pick the heavier weight yourself. A bodyweight exercise adds a rep once you reach the top of the card, whether you left effort blank or answered with the reserve it asked for. A technical lift, and a bar lift a long set breaks such as a deadlift or a bent-over row, stays at its own reps. Its card says so, and that three sessions in a row at the top earn its step, with Reps in reserve blank or at least the card’s number. A technical bodyweight exercise, such as a wall walk or a negative pull-up, keeps its reps and has no weight to step up to: its card says progress comes from harder variations. A powerlifting top set, an assisted exercise or a loaded carry needs an effort answer to earn a step, and the card on its first set says so. In a workout the Forge plans, VidarFit still lowers the load if you clearly missed the range.
The form fills in the bottom of the range, and Log set takes it as it stands. If you log a lift that way for three sessions in a row with effort blank, the card says so. If you did more, change the reps before you log the set: that’s how the weight moves.
“0 in reserve” is not failure
Zero reps in reserve means you could not have done another rep with good form. Failing a rep partway is recorded separately: tap Couldn’t finish before you log the set. The two are treated differently.
Pain
A set logged with pain stops that exercise and any other work today that loads the same area, keeps that exercise out for the rest of the day whichever area you chose (Train anyway doesn’t bring it back), offers a swap that avoids it when there is one, and keeps the set out of progression and records. It is never treated as just a hard set. Your next card for that lift goes no heavier than the load that hurt. If your plan has different kinds of day for that lift, the day that hurt keeps to that load until you’ve done it without pain at or near that weight.
What never changes
- Sets you already logged are never rewritten.
- Warm-ups are not adjusted by your working sets.
- A correction fixes a typo; it is not a fatigue signal, and it does not trigger a second adjustment.
Overriding it
Every adjusted number is still yours to change before you log. VidarFit records what you did, not what it suggested.

